Wireless Solutions – Radiofrequency

  • COMMUNICATION INTERFACE – CO KNX 001

    Communication interface between DINUY conventional Dimmers and any KNX-RF sensor.
    Compatible with all DINUY modular dimmers.
    Unidirectional communication.
    At the moment that receives a RF signal from a sensor it transmits the order to the dimmers, being possible to regulate any type of load, thanks to the wide range of available dimmers.
    The device can also be used as a KNX-RF repeater to increase the wireless range within a KNX-RF wireless system.
    Modular installation device.
    DIN-rail mounting. 1-module wide.
    Compatible with: EM KNX 002, PU KNX 001, RC KNX 001 & CO KNX 002.

  • SWITCH ACTUATOR – IT KNX 001

    Wireless 1-channel Switch actuator for general purpose.
    Up to 16A switching capacity with non-free voltage output.
    Two different operation modes:
    · Switch ON/OFF.
    · Timer: 3sec ~ 5min.
    Incorporates RF signal repeater function, which can be enabled or disabled as needed.
    A conventional pushbutton can be wired for local control.
    DIN-rail mounting.
    Dimensions: 1 module wide.230V-operated.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

  • WIRELESS INTERFACE FOR PUSHBUTTON – EM KNX 002

    • The 1 channel Universal Interface detects status changes at the inputs and sends KNX telegrams depending on its parameterisation through its switches.
    • It can be connected conventional pushbuttons or auxiliary contacts to the device.
    • The inputs are triggered by two independent input commands, for instance, by using 2 puschbuttons (N.O contacts).
    • The device provides functions like switching or dimming of lighting, moving of blinds and shutters, managing scenes,..
    • It is a flush mounted device to be inserted in an universal box, behind the pushbutton.
    • Battery-operated, 2 x 3V Lithium batteries CR2025. Useful life higher than 8 years.
    • Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1, RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 and RE KNX DA1.
  • 1-CHANNEL SWITCH ACTUATOR – MI KNX 001

    Wireless 1-channel Switch actuator for general purpose.
    Up to 16A switching capacity with non-free voltage output.
    Two different operation modes:
    · Switch ON/OFF.
    · Timer: 3sec ~ 5min.Incorporates RF signal repeater function, which can be enabled or disabled as needed.
    A conventional pushbutton can be wired for local control.Junction box mounting.
    Dimensions: 46 x 46 x 30mm. 230V-operated.
    Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 003, DM KNX 001, DM KNX 002 & CO KNX 002.

  • COMMUNICATION KNX RF/TP GATEWAY – CO KNX 002

    The Media Coupler connects wireless KNX devices (KNX-RF) with the KNX Bus (KNX-TP).
    Therefore wired actuators can be controlled by wireless sensors as well as wireless actuators can be controlled by wired transmitters (bidirectional communication).
    Can be used together with devices to control lighting, HVAC, blinds/shutters and main purpose devices.In addition to its function as media coupler, the device can also be used as a KNX-RF repeater to increase the wireless range within a KNX-RF wireless system.
    Commissioning by ETS4 or later version.
    Dimensions: 78 x 28 x 23mm.
    It is installed in a flush-mounted device box and obtains its power supply via the KNX bus line.

  • PORTABLE PUSHBUTTON – PU KNX 001

    • The 1 channel Pushbutton sends KNX telegrams when the button is pressed depending on its parameterisation through its switches.
    • The device provides functions like switching or dimming of lighting, moving of blinds and shutters, managing scenes,…
    • Dimensions: 78 x 28 x 23mm.
    • Portable or wall fix mounted.
    • Battery-operated: 2 x 3V Lithium batteries CR2025. Useful life higher than 8 years.
      • Compatible with: CO KNX 001, IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1, RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 010 and RE KNX DA1.
  • 2-CHANNEL SWITCH OR 1-CHANNEL BLIND/SHUTTER ACTUATOR – PE KNX 001

    • Wireless 1-channel blind/shutter actuator or 2-channel switching actuator.
    • Up to 16A switching capacity per channel with 2 free-voltage outputs.
    • Incorporates RF signal repeater function, which can be enabled or disabled as needed.
    • Includes 2 auxiliary inputs which allow the local control.
    • Dimensions: 107 x 53 x 34mm.
    • 230V-operated.
    • Compatible with: EM KNX 002, PU KNX 001, RC KNX 001, SE KNX 002 & CO KNX 002.
  • CONTROL SOFTWARE – CO KNX 004

    KNX-RF USB interface stick with visualization and control software (Virtual Remote Control).
    Function: establishes a bidirectional communication between a PC and the KNX-RF installation and alows the control of lighting, HVAC or blinds/shutters without wires.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).

  • REMOTE CONTROL – RC KNX 001

    • The Radio Remote Control sends KNX telegrams when one of the key is presse depending on its parameterisation.
    • The KNX-RF hand-held remote control transmits KNX telegrams wirelessly when the key is pressed.
    • These could include telegrams for switching, dimming, blind/shutter control or lighting scenes saving/recovering.
    • Incorporates 5 independent channels, 1 main channel and 5 scene channels.
    • Battery-operated: 1 x 3V Lithium battery CR2032. Useful life higher than 8 years.
    • Power supply: 1X3V battery CR2032. Useful life: > 8 years.
    • Radio-frequency: 868,4 MHz.
    • Range: up to 100m (in the free field).
    • Compatible with: CO KNX 001. IT KNX 001, CO KNX 002, PE KNX 001, MI KNX 001, RE KNX LE1, RE KNX LE2, RE KNX LE3, RE KNX RGB, RE KNX 01 & RE KNX DA1.
  • MOTION DETECTOR – DM KNX 001

    Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
    Built-in light sensor, allowing to limit the operation of the detector to daylight.
    It has 2 operation modes:
    Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 and CO KNX 002.
    Presence detector: useful for heating and air conditioning control.
    Compatible with the actuators: TM KNX 001 and CO KNX 002.
    Incorporates Temperature sensor.
    Coverage: 360º and Ø7m at 2.5 high.
    Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
    Radio-frequency: 868,4MHz.

  • THERMOSTAT – TM KNX 001

    Wireless 1-channel Thermostat actuator for HVAC control.
    It incorporates a potentiometer which allows setting the desired temperature avoiding any undesired manipulation.
    Every time it receives a signal of temperature from the sensor it will be compared with the already set in the thermostat and will act accordingly on its relay.
    It also can receive telegrams from door/window contacts or presence detectors.
    Up to 16A switching capacity with free-voltage relay.
    Incorporates RF signal repeater function, which can be enabled or disabled as needed.
    Modular installation device. DIN-rail mounting. 1-module wide.
    230V-operated.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: SE KNX 001, SE KNX 003, SE KNX 004, DP KNX 001 & CO KNX 002.

  • KNX-RF SIGNAL REPEATER – AM KNX 001

    • RF signal repeater. It enlarges the range between transmitters and actuators.
    • Up to 3 consecutive units can be used in the same installation.
    • Compatible with: any KNX-RF signal.
  • MOTION DETECTOR – DM KNX 002

    Wireless wall-mounted Infrared PIR motion detector for lighting control.
    Built-in light sensor, allowing to limit the operation of the detector to daylight.
    As soon as it detects movement, the sensor sends the ON signal to the linked receiver and its contact keeps closed. The ON time must be set on the receiver.
    Wall or ceiling mounting installation.
    Coverage: 180º and Ø10m at 2m high.
    Power Supply: 2 x 3V AA Lithium batteries L91. Working life over 15 years.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: IT KNX 001, MI KNX 001 and CO KNX 002.

  • WIRELESS DIMMER FOR LED LAMPS – RE KNX LE1

    • Wireless Dimmer for LED lamps.
    • Leading or Trailing edge dimming technology:
      • Leading-edge dimmable 230V LED lamps.
      • Trailing-edge dimmable 230V LED lamps.
      • Dimmable 12V LED lamps with electronic transformer.
      • Incandescent and 230V Halogen lamps.
      • LV Halogen lamps with electronic transformer.
    • Power capacity of up to 250W, depending on the type of lamp.
    • A conventional Pushbutton can be wired.
    • Junction-box mounting.
    • Compatible with: EM KNX 002, PU KNX 001, RC KNX 001 & CO KNX 002.
    • Maximum range of up to 100m (in free field).
  • TEMPERATURE SENSOR – SE KNX 001

    Wireless Temperature value transmitter.
    Sends the temperature value measured in the place when:
    · The temperature value changes more than ±0,5ºC.
    · 60 minutes after the last transmission.
    · Pressing the inside link key.
    Dimensions: 78 x 28 x 23mm.
    Portable or wall fix mounted.
    Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001 & CO KNX 002.

  • WIRELESS DIMMER FOR SINGLE-COLOR LED STRIPS – RE KNX LE2

    • Wireless 1-channel Dimmer for 12V-48V single-color LED Strips.
    • Pulse Width Modulation (PWM) dimming technology.
    • Up to 8A dimming capacity (12V: 96W // 24V: 192W).
    • A conventional pushbutton can be wired.
    • Junction box mounting. Dimensions: 55 x 53 x 34mm.
    • Memory function.
    • Compatible with: EM KNX 002, PU KNX 001, RC KNX 001 and CO KNX 002.
    • Maximum range of up to 100m (in free field).
  • BRIGHTNESS SENSOR – SE KNX 002

    Wireless Luminosity value transmitter for Sun protection function.
    It is designed for the automatic control of shutters or blinds.
    According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
    Luminosity is measured by the sensor attached to the window with a sticker.
    Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
    Dimensions: 78 x 28 x 23mm.
    Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
    Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: PE KNX 001 & CO KNX 002.

  • WIRELESS DIMMER FOR SINGLE-COLOR LED STRIPS – RE KNX LE3

    • Wireless 1-channel Dimmer for 12V-48V single-color LED Strips.
    • Pulse Width Modulation (PWM) dimming technology.
    • Up to 4A dimming capacity (12V: 48W // 24V: 96W).
    • Memory function.
    • Compatible with: EM KNX 002, PU KNX 001, RC KNX 001 and CO KNX 002.
    • Maximum range of up to 100m (in free field).
  • DOOR/ WINDOW SENSOR – SE KNX 003

    Wireless Door/Window contact transmitter.
    Detects the state (closed/open) of a door or window over the reed contact integrated in the device.
    Each telegram is sent twice ensuring a highest security in the transmission.
    Installation in the frame of a door or window.
    Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
    Dimensions: 78 x 28 x 23mm.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001, IT KNX 001, MI KNX 001 & CO KNX 002.

  • WIRELESS DIMMER FOR RGB LED STRIPS – RE KNX RGB

    • Dimmer for 3-channels RGB 12-48V LED strips.
    • PWM dimming technology.
    • Control by RF remote control: RC KNX 001.
    • Maximum load of up to 5A/channel.
    • Maximum range of up to 100m (in free field).
  • TEMPERATURE SENSOR – SE KNX 004

    Wireless Temperature sensor with desired temperature value control knob.
    This sensor sends the following variables:
    · Measured temperature value.
    · Temperature setpoint value.
    · State (Standby or Auto).
    Incorporates a wheel to set the desired temperature in the room.
    Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
    Dimensions: 80 x 30 x 26mm.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001 & CO KNX 002.

  • WIRELESS DIMMER FOR 1-10V DRIVERS – RE KNX 010

    • Wireless Dimmer for 1-10V Ballast or LED Driver, for example, Fluorescence or LED lighting fixtures.
    • Can control up to a maximum of 100 equipments.
    • Junction-box mounting.
    • Control by RF-KNX transmitter (remote control, pushbutton,…) or wired Pushbutton.
    • Resettable protection against overloads, short-circuits and over-heating.
    • Compatible with several transmitters: EM KNX 002, PU KNX 001 and RC KNX 001.
    • Maximum range of up to 100m (in free field).
  • TEMPERATURE SENSOR – SE KNX 005

    Wireless Temperature sensor transmitter with Probe for heating floors.
    It sends the temperature value in the place where the probe is installed.
    Specially-indicated for underfloor heating installations.
    Includes the following components:
    · Transmitter: captures the value from the temperature probe and transmits it via RF to the linked receiver.
    · Temperature probe: measures the temperature sensed at the tip of the probe. Must be connected directly to the transmitter via its original cable, which is double insulated. Tip of the probe is waterproof.
    The temperature value is sent every minute.
    Incorporates RF signal repeater function, which can be enabled or disabled as needed.
    Power supply: 230V~ 50Hz.
    Dimensions: 45 x 42 x 12mm.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001 & CO KNX 002.

  • WIRELESS DIMMER FOR DALI BALLAST OR DRIVER – RE KNX DA1

    • Wireless Dimmer for DALI Ballast or LED Driver, for example, Fluorescence or LED lighting fixtures.
    • Can control up to a maximum of 64 DALI equipments.
    • DALI Broadcast communication.
    • Control by wireless RF-KNX transmitter (remote control, pushbutton,…) or wired Pushbutton.
    • Built-in selector switch which allows to set the minimum dimming level.
    • Resetteable protection against overloads, short-circuits and over-heating.
    • Junction-box mounting.
    • Compatible with: EM KNX 002, PU KNX 001, RC KNX 001 & CO KNX 002.
    • Maximum range of up to 100m (in free field).

Este sitio web utiliza cookies para que usted tenga la mejor experiencia de usuario. Si continúa navegando está dando su consentimiento para la aceptación de las mencionadas cookies y la aceptación de nuestra política de cookies, pinche el enlace para mayor información.plugin cookies

ACEPTAR
Aviso de cookies