Emisors/Sensors

Showing all 6 results

  • MOTION DETECTOR – DM KNX 001

    Wireless flush-ceiling mounted Infrared PIR motion detector for lighting, heating and air conditioning control.
    Built-in light sensor, allowing to limit the operation of the detector to daylight.
    It has 2 operation modes:
    Motion detector: useful for lighting control. The time delay must be set on the actuator. Compatible with the actuators: IT KNX 001, MI KNX 001 and CO KNX 002.
    Presence detector: useful for heating and air conditioning control.
    Compatible with the actuators: TM KNX 001 and CO KNX 002.
    Incorporates Temperature sensor.
    Coverage: 360º and Ø7m at 2.5 high.
    Battery-operated, 1 x 3V Lithium battery LS14250. Useful life higher than 4 years.
    Radio-frequency: 868,4MHz.

  • TEMPERATURE SENSOR – SE KNX 001

    Wireless Temperature value transmitter.
    Sends the temperature value measured in the place when:
    · The temperature value changes more than ±0,5ºC.
    · 60 minutes after the last transmission.
    · Pressing the inside link key.
    Dimensions: 78 x 28 x 23mm.
    Portable or wall fix mounted.
    Battery-operated, 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001 & CO KNX 002.

  • BRIGHTNESS SENSOR – SE KNX 002

    Wireless Luminosity value transmitter for Sun protection function.
    It is designed for the automatic control of shutters or blinds.
    According to the measured luminosity, it controls the raising or lowering of the shutters/ blinds to provide sun protection.
    Luminosity is measured by the sensor attached to the window with a sticker.
    Incorporates 4 different operation modes configurable by two small switches: Solar Alarm, Blind Control, Blind Control with manual lift and Lux Sensor.
    Dimensions: 78 x 28 x 23mm.
    Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
    Power supply: 1X3V baterry CR2032. Useful life: > 8 years.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: PE KNX 001 & CO KNX 002.

  • DOOR/ WINDOW SENSOR – SE KNX 003

    Wireless Door/Window contact transmitter.
    Detects the state (closed/open) of a door or window over the reed contact integrated in the device.
    Each telegram is sent twice ensuring a highest security in the transmission.
    Installation in the frame of a door or window.
    Battery-operated: 2 x 3V Lithium batteries CR2032. Useful life higher than 8 years.
    Dimensions: 78 x 28 x 23mm.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001, IT KNX 001, MI KNX 001 & CO KNX 002.

  • TEMPERATURE SENSOR – SE KNX 004

    Wireless Temperature sensor with desired temperature value control knob.
    This sensor sends the following variables:
    · Measured temperature value.
    · Temperature setpoint value.
    · State (Standby or Auto).
    Incorporates a wheel to set the desired temperature in the room.
    Battery-operated: 1 x 3V Lithium battery CR2450. Useful life higher than 8 years.
    Dimensions: 80 x 30 x 26mm.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001 & CO KNX 002.

  • TEMPERATURE SENSOR – SE KNX 005

    Wireless Temperature sensor transmitter with Probe for heating floors.
    It sends the temperature value in the place where the probe is installed.
    Specially-indicated for underfloor heating installations.
    Includes the following components:
    · Transmitter: captures the value from the temperature probe and transmits it via RF to the linked receiver.
    · Temperature probe: measures the temperature sensed at the tip of the probe. Must be connected directly to the transmitter via its original cable, which is double insulated. Tip of the probe is waterproof.
    The temperature value is sent every minute.
    Incorporates RF signal repeater function, which can be enabled or disabled as needed.
    Power supply: 230V~ 50Hz.
    Dimensions: 45 x 42 x 12mm.
    Radio-frequency: 868,4MHz.
    Range: up to 100m (in the free field).
    Compatible with: TM KNX 001 & CO KNX 002.

Este sitio web utiliza cookies para que usted tenga la mejor experiencia de usuario. Si continúa navegando está dando su consentimiento para la aceptación de las mencionadas cookies y la aceptación de nuestra política de cookies, pinche el enlace para mayor información.plugin cookies

ACEPTAR
Aviso de cookies