Actuators

Showing all 8 results

  • 1-CHANNEL KNX-RF SWITCHING ACTUATOR – MI K5X 001

    • 1-channel Wireless KNX-RF S-Mode wireless Switching Actuator.
    • Normally open contact, not free of voltage, 16A relay.
    • Saving and calling up to 5 Scenes.
    • Staircase Time Switch function.
    • Incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers.
    • Flush-mounted into junction box. Dimensions: 46 x 46 x 30mm.
    • Wired Pushbutton can be connected with configurable operation.
    • Supplied by the 230V mains.
    • Programming and commissioning by ETS5 or later version.

  • 2-CHANNEL KNX-RF SWITCHING/BLIND ACTUATOR WITH 4 INPUTS – PE K5X 001

    • KNX-RF S-Mode Wireless 1-channel Switching Actuator:

    – 2-channel Switching Actuator.
    – 1-channel Blind/Shutter Actuator.

    • If it is configured as 2-channel Switch Actuator, the following functions are available in each channel: Timer, Preset value, Scene control, Logical functions, Forzed and Threshold function.
    • If it is configured as 1-channel Blinds/Shutters Actuator, the following alarms and functions are available: Wind alarm, Rain alarm, Frost alarm, Sun Protection function, Scene control and Forzed function.
    • Incorporates 4 Analog/Digital inputs, which can be configured independently, through the ETS:

    – Digital inputs (binary): allows the connection of a pushbutton, switch or conventional binary sensor, free-voltage contact.
    – Analog inputs: allows the connection of a temperature probe (ST KNT 001 or ST KNT 002).

    • In addition, it allows enabling and configuring up to 4 independent Cooling or Heating Thermostats.
    • Programming and commissioning via ETS5 or later version.

  • 2-CHANNEL KNX-RF SWITCHING/BLIND ACTUATOR – PE K5X 002

    • KNX-RF S-Mode Wireless 1-channel Switching Actuator:

    – 2-channel Switching Actuator.
    – 1-channel Blind/Shutter Actuator.

    • If it is configured as 2-channel Switch Actuator, the following functions are available in each channel: Timer, Preset value, Scene control, Logical functions, Forzed and Threshold function.
    • If it is configured as 1-channel Blinds/Shutters Actuator, the following alarms and functions are available: Wind alarm, Rain alarm, Frost alarm, Sun Protection function, Scene control and Forzed function.
    • Programming and commissioning via ETS5 or later version.

  • 1-CHANNEL RLC+LED KNX-RF DIMMING ACTUATOR – RE K5X LE1

    • 1-channel KNX-RF S-Mode Wireless Dimming Actuator for LED lamps.
    • Compatible with leading- or trailing-edge dimmable lamps:

    – Dimmable 230V LED lamps.
    – Dimmable 12V LED lamps with electronic transformer.
    – Incandescent or 230V Halogen lamps.
    – LV Halogen lamps with electronic transformer.

    • Incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers.
    • Auxiliary Pushbutton input with configurable operation.
    • Flush mounted into junction box.
    • Programming and commissioning by ETS5 or later version.

  • 1-CHANNEL LED STRIP KNX-RF DIMMING ACTUATOR – RE K5X LE2

    • 1-channel KNX-RF S-Mode Wireless Dimming Actuator for Single-color low-voltage LED Strips.
    • Power supply: 12-48VDC.
    • Different functions which can be configured with ETS:

    – Soft Switch On and Off.
    – Maximum and minimum dimming level.
    – Behavior after On telegram.

    • Staircase time switch and Sequential functions.
    • Auxiliary Pushbutton input with configurable operation.
    • It incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers.
    • Adjustable behavior in case of bus voltage failure.
    • Saving and calling up to 5 Scenes.
    • Flush mounted into junction box.
    • Programming and commissioning by ETS5 or later version.

  • 3-CHANNEL RGB LED STRIPS KNX-RF DIMMING ACTUATOR – RE K5X RGB

    • 3-channel KNX-RF S-Mode Wireless Dimming Actuator for RGB LED Strips.
    • Control of RGB or Single-colored LED Strips via Pulse Width Modulation (PWM).
    • Different functions are configurable via ETS, e.g.:

    – Control of 1 RGB LED Strip or 3 Single-colored LED Strips.
    – Soft Switch On and Off.
    – Minimum and maximum dimming level.

    • Staircase time switch with pre-warning function.
    • Up to 5 Scenes and 5 Sequences can be stored / called up.
    • It has 4 Analog/Digital inputs, which can be configured independently, through the ETS:
    • Digital inputs (binary): allows the connection of a pushbutton, switch or conventional binary sensor, free-voltage contact.
    • Analog inputs: allows the connection of a temperature probe (ST KNT 001 or ST KNT 002).
    • Each of the four inputs has the following functions: Switch, Dimmer, Multiple Dimmer, Sequential Switch, Blind Control, Scene Control, Fixed/Forced Function, Counter, Temperature Sensor and RGB colours.
    • In addition, it allows to enable and configure up to 4 independent Thermostats.
    • Programming and commissioning via ETS5 or later version.

  • 1-CHANNEL KNX-RF 1-10V DIMMING ACTUATOR – RE K5X 010

    • 1-channel KNX RF S-Mode Wireless 1-10V Dimming Actuator for Drivers or Ballasts.
    • Built-in relay which allows to disconnect completely the supply of the luminaires.
    • Different functions which can be configured with ETS:

    – Soft Switch On/Off.
    – Maximum and Minimum dimming level.
    – Behavior after ON telegram.

    • Saving and calling up to 5 Scenes.
    • Staircase time switch and Sequential operation modes.
    • Auxiliary Pushbutton input with configurable operation.
    • Incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers.
    • Flush mounted into junction box.
    • Programming and commissioning by ETS5 or later version.

  • 1-CHANNEL DALI KNX-RF DIMMING ACTUATOR – RE K5X DA1

    • 1-channel KNX RF S-Mode Wireless Dimming Actuator for DALI Drivers or Ballasts, with LED or Fluorescence lighting.
    • Broadcast and uni-directional DALI communication.
    • Up to 64 DALI ECGs can be controlled.
    • Different functions which can be configured with ETS:

    – Soft Switch On and Off.
    – Maximum and minimum dimming level.

    • Staircase time switch and Sequential functions.
    • Auxiliary Pushbutton input with configurable operation.
    • Saving and calling up to 5 Scenes.
    • Flush mounted in junction box.
    • Programming and commissioning by ETS5 or later versions.

Este sitio web utiliza cookies para que usted tenga la mejor experiencia de usuario. Si continúa navegando está dando su consentimiento para la aceptación de las mencionadas cookies y la aceptación de nuestra política de cookies, pinche el enlace para mayor información.plugin cookies

ACEPTAR
Aviso de cookies