KNX Radio Frecuency Devices - System Mode
Showing 1–9 of 18 results
-
1-CHANNEL KNX-RF SWITCHING ACTUATOR – MI K5X 001
• 1-channel Wireless KNX-RF S-Mode wireless Switching Actuator.
• Normally open contact, not free of voltage, 16A relay.
• Saving and calling up to 5 Scenes.
• Staircase Time Switch function.
• Incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers.
• Flush-mounted into junction box. Dimensions: 46 x 46 x 30mm.
• Wired Pushbutton can be connected with configurable operation.
• Supplied by the 230V mains.
• Programming and commissioning by ETS5 or later version. -
2-CHANNEL INPUT PUSHBUTTON KNX-RF INTERFACE – EM K5X 002
• Wireless KNX-RF S-Mode Pushbutton Interface which allows the control of Switching, Dimming or Blinds Actuators.
• Incorporates 2 inputs, each of which can be parameterized individually through the ETS:• Control of 1 or 2 independent output channels.
– Function of each input: Switch, Staircase Time Switch, Dimmer, Multiple Switch, Shutter control, Scene control, Fixed value/Forced.• The Temperature Sensor incorporates different options that can also be parameterized:
– Transmission frequency.
– Over-heating or over-cooling alarms.
– Temperature sensor calibration.• Its small housing allows to be flush mounted into a universal box, behind the pushbutton. Dimensions: 45 x 45 x 12mm.
• Battery-operated: 2 x 3V Lithium Battery CR2025. Useful life higher than 8 years.
• Programming and commissioning via ETS5 or later versions. -
KNX RF USB STICK – CO K5X 001
- This interface allows establishing a bidirectional connection between a PC or a laptop and the KNX RF wireless network.
- The device complies with the specification of KNX RF and supports the protocol cEMI.
- The interface is compatible with ETS 5 (or higher).
- The power is supplied via the USB port.
-
2-CHANNEL KNX-RF SWITCHING/BLIND ACTUATOR WITH 4 INPUTS – PE K5X 001
• KNX-RF S-Mode Wireless 1-channel Switching Actuator:
– 2-channel Switching Actuator.
– 1-channel Blind/Shutter Actuator.• If it is configured as 2-channel Switch Actuator, the following functions are available in each channel: Timer, Preset value, Scene control, Logical functions, Forzed and Threshold function.
• If it is configured as 1-channel Blinds/Shutters Actuator, the following alarms and functions are available: Wind alarm, Rain alarm, Frost alarm, Sun Protection function, Scene control and Forzed function.
• Incorporates 4 Analog/Digital inputs, which can be configured independently, through the ETS:– Digital inputs (binary): allows the connection of a pushbutton, switch or conventional binary sensor, free-voltage contact.
– Analog inputs: allows the connection of a temperature probe (ST KNT 001 or ST KNT 002).• In addition, it allows enabling and configuring up to 4 independent Cooling or Heating Thermostats.
• Programming and commissioning via ETS5 or later version. -
230V-OPERATED 4-CHANNEL KNX-RF BINARY/ANALOG INPUT – EM K5X 004
• 230V-operated KNX-RF S-Mode Wireless Transmitter with 4 Binary or Analog Inputs.
• Each of the 4 inputs can be individually parameterized through the ETS:– Binary Input (pushbutton): Switch, Dimmer, Multiple Switch, Sequential Switch, Blinds Control, Scenes Management, Value Transmitter, Pulse Counter.
– Analog Input: Temperature Sensor, connecting the DINUY probes “ST KNT 001” or “ST KNT 002”.
– Motion Detector Input: connecting DINUY’s motion detector “DM KNT 004”.• Incorporates up to 4 independent Thermostats for the control of Heating and / or Cooling of 4 different zones.
• Supplied by the 230V mains.
• Programming and commissioning via ETS5 or later version. -
KNX RF/TP MEDIA COUPLER – CO K5X 002
- The KNX RF/TP Coupler is a compact KNX radio coupler.
- It connects KNX RF devices of a radio line with the KNX Bus Twisted Pair.
- The device has a filter table (8k byte). The coupler supports long frames and is compatible with the ETS® software ETS5 or higher.
- The buttons on the front panel allow disabling the telegram filter for testing purposes.
- The LEDs indicate operating conditions as well as communication errors on the KNX bus.
- The power is supplied via the KNX bus (main line).
-
2-CHANNEL KNX-RF SWITCHING/BLIND ACTUATOR – PE K5X 002
• KNX-RF S-Mode Wireless 1-channel Switching Actuator:
– 2-channel Switching Actuator.
– 1-channel Blind/Shutter Actuator.• If it is configured as 2-channel Switch Actuator, the following functions are available in each channel: Timer, Preset value, Scene control, Logical functions, Forzed and Threshold function.
• If it is configured as 1-channel Blinds/Shutters Actuator, the following alarms and functions are available: Wind alarm, Rain alarm, Frost alarm, Sun Protection function, Scene control and Forzed function.
• Programming and commissioning via ETS5 or later version. -
KNX-RF WIRELESS TEMPERATURE SENSOR – SE K5X 001
• Wireless KNX-RF S-Mode Temperature sensor.
• The Sensor will transmit the value measured by the temperature sensor.
• The Temperature Sensor incorporates different options that must be parameterized using the ETS:– Transmission frequency: according to the time or temperature change.
– Over-heating or over-cooling alarms.
– Temperature sensor calibration.
• Portable or wall mounting.
• Dimensions: 78 x 28 x 23mm.
• Battery powered, 2 x 3V CR2032 lithium batteries. Useful life higherthan 8 years.
• Programming and commissioning by ETS5 or later version. -
1-CHANNEL RLC+LED KNX-RF DIMMING ACTUATOR – RE K5X LE1
• 1-channel KNX-RF S-Mode Wireless Dimming Actuator for LED lamps.
• Compatible with leading- or trailing-edge dimmable lamps:– Dimmable 230V LED lamps.
– Dimmable 12V LED lamps with electronic transformer.
– Incandescent or 230V Halogen lamps.
– LV Halogen lamps with electronic transformer.• Incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers.
• Auxiliary Pushbutton input with configurable operation.
• Flush mounted into junction box.
• Programming and commissioning by ETS5 or later version.