KNX Dinulink

Showing 1–9 of 60 results

• 

  Switching actuator with 4 output channels and dimmer for RGBW LED strips – IR KNT 044

  • Multifunction actuator that can wok as a dimmer for RGBW LED strips with 4 output channels and:
    • Switching of 4 independent output channels
    • Actuator for Blinds/Awnings with 2 output channels
    • 1 Fan-Coil Actuator with 2 pipes (On/Off Valve and 3 Fan Speeds).
  • Installation on DIN rail.
  • Manual forcing of each channel by means of buttons on the front of the actuator, without the need for a Bus connection.
  • Possibility of 12 Binary and/or Analog Inputs: 8 Binary + 4 Binary/Analog.
  • Status LED indicators for each output channel.
  • LED status indicators for error status.
  • It is possible to enable up to 8 different functions: timer, scenes, logic operations, forced operation, etc.
  • Programming and commissioning using ETS5, or later versions.
• 

  TOUCHLESS 1-GANG BLACK PUSHBUTTON – PU KNT PR1

  • Proximity pushbutton, non-contact, 1-channel KNX, with Black glass and Copper color frame.
  • Glass surface.
  • It incorporates 2 RGB LEDs configurable by ETS.
  • It has the following functions:

  – Switching and regulation of lighting.
  – Control of Blinds and Awnings.
  – Sending of any type of value (brightness, temperature, etc).

  • Management and memorization of 1 Scene.
  • Detection distance adjustable by parameter.
  • Built-in temperature sensor.
  • Programming and commissioning using ETS5 or later versions.

• 

  TOUCHLESS 1-GANG WHITE PUSHBUTTON – PU KNT PR2

  • Proximity pushbutton, non-contact, 1-channel KNX, with Black glass and Copper color frame.
  • Glass surface.
  • It incorporates 2 RGB LEDs configurable by ETS.
  • It has the following functions:

  – Switching and regulation of lighting.
  – Control of Blinds and Awnings.
  – Sending of any type of value (brightness, temperature, etc).

  • Management and memorization of 1 Scene.
  • Detection distance adjustable by parameter.
  • Built-in temperature sensor.
  • Programming and commissioning using ETS5 or later versions.

• 

  1-CHANNEL KNX-RF SWITCHING ACTUATOR – MI K5X 001

  • 1-channel Wireless KNX-RF S-Mode wireless Switching Actuator.
  • Normally open contact, not free of voltage, 16A relay.
  • Saving and calling up to 5 Scenes.
  • Staircase Time Switch function.
  • Incorporates the KNX-RF signal repeater function (optional), which allows extending the distance between transmitters and receivers.
  • Flush-mounted into junction box. Dimensions: 46 x 46 x 30mm.
  • Wired Pushbutton can be connected with configurable operation.
  • Supplied by the 230V mains.
  • Programming and commissioning by ETS5 or later version.

• 

  2-CHANNEL INPUT PUSHBUTTON KNX-RF INTERFACE – EM K5X 002

  • Wireless KNX-RF S-Mode Pushbutton Interface which allows the control of Switching, Dimming or Blinds Actuators.
  • Incorporates 2 inputs, each of which can be parameterized individually through the ETS:

  • Control of 1 or 2 independent output channels.
  – Function of each input: Switch, Staircase Time Switch, Dimmer, Multiple Switch, Shutter control, Scene control, Fixed value/Forced.

  • The Temperature Sensor incorporates different options that can also be parameterized:

  – Transmission frequency.
  – Over-heating or over-cooling alarms.
  – Temperature sensor calibration.

  • Its small housing allows to be flush mounted into a universal box, behind the pushbutton. Dimensions: 45 x 45 x 12mm.
  • Battery-operated: 2 x 3V Lithium Battery CR2025. Useful life higher than 8 years.
  • Programming and commissioning via ETS5 or later versions.

• 

  2-CHANNEL SWITCH/BLIND ACTUATOR – IT KNT 001

  • 2-channel Switching Actuator or 1-channel Blinds / Awnings Actuator.
  • Maximum switching capacity of up to 16A per channel, 2 voltage-free contacts.
  • Modular housing (1 module wide), DIN-rail mounting.
  • Incorporates 2 potentiometers, each of which allows manual control in the form of a test, without the need for the Bus.
  • It is possible to enable different functions: timer, preset, scenes, logic operations, forced operation …
  • Programming and commissioning using ETS3, or later versions.

• 

  640mA POWER SUPPLY – FA KNT 001

  • 640mA Power Supply which produces and monitors EIB/KNX system voltage.
  • The bus line is decoupled from the power supply with the integrated choke.
  • The power supply is connected to the bus line with a bus connection terminal.
  • A 30VDC auxiliary voltage is made available via an additional connection terminal. This voltage can be used to supply a further bus line (in connection with a separate choke).

• 

  KNX RF USB STICK – CO K5X 001

  • This interface allows establishing a bidirectional connection between a PC or a laptop and the KNX RF wireless network.
  • The device complies with the specification of KNX RF and supports the protocol cEMI.
  • The interface is compatible with ETS 5 (or higher).
  • The power is supplied via the USB port.
• 

  LAÜKA CAPACITIVE BLACK SWITCH 4 BUTTONS & RGB BACKLIT – PU KNT 001

  • 4-gang Laüka Capacitive Multifunction Pushbutton with Black glass and RGB backlit.
  • Customizable RGB backlit and lighted icons: Laüka Configurator
  • Glass touch surface.
  • Designed to provide the user with absolute control over lighting, blinds and, in turn, the management of Scenes.
  • Each of the 4 touch keys has the following functions:

  – Lighting Switching and Dimming.
  – Blinds, Shutters and Awnings Control.
  – Value Transmitter (brightness, temperature, etc.).
  – Management of lighting scenarios.

  • Incorporates Temperature Sensor and Heating and / or Cooling Thermostat.
  • Programming and commissioning via ETS4 or later versions.